Furnace Repair in Mississauga & Peel Region
Forced-air gas furnace blowing cold air, short cycling, or refusing to start when temperatures drop? Real Deal HVAC responds 24/7 from our Mississauga dispatch base with stocked diagnostic vans and a written price before any tool touches your equipment.
Book Furnace Repair
Staff confirm your appointment window by phone or text.
Common Furnace Problems & What They Mean
Match what your furnace is doing to the likely cause and what is safe for you to check. Anything involving the burners, gas valve, ignition, or wiring is ours to handle.
| What You Notice | Likely Cause | When to Call Us |
|---|---|---|
| Furnace blowing cold air | Dirty flame sensor, cracked hot surface igniter, or high-limit switch tripping from restricted airflow across a clogged filter. | Call us if the air stays cool after a clean filter and a thermostat reset — the igniter or flame sensor likely needs service. |
| Furnace won't start at all | No call for heat from the thermostat, tripped breaker, furnace wall switch off, or a locked-out control board after repeated failed ignition attempts. | Call us if power and thermostat check out but the unit is silent — the inducer, pressure switch, or ignition board is the likely culprit. |
| Short cycling (starts, stops, repeats) | Overheating from poor airflow, a stuck high-limit switch, an oversized unit, or a partially blocked flue / pressure switch hose. | Call us if short cycling continues after clearing airflow — overheating will crack a heat exchanger if left running. |
| Loud banging or rumbling on startup | Delayed gas ignition — burners light late and ignite a larger pocket of gas with a bang. Often dirty burners or a weak igniter. | Call us before running the furnace again. Delayed ignition stresses the heat exchanger and is a safety concern. |
| Runs but home never reaches setpoint | Undersized or aging unit, leaky ductwork, a failing secondary heat exchanger, or a thermostat reading the wrong temperature. | Call us to measure supply temperature, static pressure, and duct leakage before the coldest stretch of winter. |
| Error code flashing on the control board | The board stores a fault — flame rollout, pressure switch, limit, or ignition failure — and blinks a numbered code through the sight glass. | Call us and read us the blink count — it pinpoints the exact sensor or safety that tripped. |
What Our Furnace Repair Includes
Included
- Full diagnostic of ignition, flame rectification, safeties, and gas pressure
- Repairs to flame sensors, igniters, inducers, blowers, capacitors & gas valves
- Static pressure and supply-temperature check after the repair
- Fixed, written price approved by you before any work begins
- All gas work performed by our own licensed TSSA gas fitter
Not Included (Quoted Separately)
- Full furnace replacement / new installation — see our furnace installation page
- Cracked heat exchanger replacement (often a replace-vs-repair decision)
- Whole-home ductwork modifications or new runs
- Seasonal maintenance plans — see our maintenance plans
What Happens After You Request Service
Your request is reviewed by our staff — it is not auto-booked. We confirm your window with you before any technician is dispatched.
You submit the form
Tell us the symptom, your address, city, and a preferred window. We log it instantly.
Staff review & confirm
We check technician availability and confirm your exact appointment by phone or text — no auto-scheduling.
On-site diagnosis
A licensed gas fitter arrives in a stocked van, finds the root cause, and reads you a fixed written price.
Repair, your way
You approve the price in writing. We complete the repair and verify safe operation before we leave.
Furnace Components We Repair & Replace
Flame Sensors & Igniters
The flame sensor confirms a clean gas flame; the hot surface igniter lights the burners. Carbon or hairline cracks cause immediate lockout and are the most common no-heat fix.
Inducer Draft Motors
Clears combustion gases and closes the pressure switch so gas can flow. A seized or weak inducer prevents ignition entirely and trips a pressure-switch error code.
Blower Motors & Capacitors
Moves heated air through the ducts. A failed run capacitor makes the motor hum, overheat, and shut off on thermal limit. We stock common frame sizes on every van.
Gas Valves
Modulates gas flow to the burners. A valve that won't open or sticks on a single stage causes no-heat or uneven firing. We meter manifold pressure on every service call.
High-Limit & Rollout Switches
Safety cut-outs that stop the burner if airflow is blocked or flames roll the wrong way. Tripped switches are a symptom, not the fault — we find the upstream cause.
Control & Ignition Boards
Sequence the start-up, monitor safeties, and store diagnostic codes. We replace failed boards and verify the flame rectification circuit at the same time.
How Furnace Repair Pricing Works
Furnace repairs are diagnosed on-site and priced as a fixed, written quote — the parts and labour are listed before any work begins, so there are no surprises. For full new-unit installs we publish an installed-price catalog so you can compare options before a technician visit. See our transparent pricing list or use the instant estimate tool for a fast ballpark. A diagnostic/trip fee applies and is disclosed before dispatch.
Furnace Repair Across the Western GTA
We dispatch from our Churchill Meadows, Mississauga base to the whole western GTA — fast for no-heat calls in Mississauga, Oakville, Etobicoke, Burlington, and Milton. For an urgent mid-winter outage, also see our emergency furnace repair line, answered 24/7.
Furnace Repair FAQs
Who repairs furnaces in Mississauga and the surrounding GTA?
Real Deal HVAC does. Our own licensed TSSA gas fitter performs all gas-side furnace work from our Churchill Meadows, Mississauga dispatch base, with fast response across Oakville, Etobicoke, Burlington, and Milton. Call (647) 280-6626 any time, day or night.
Why is my furnace blowing cold air?
The three most common causes are a dirty flame sensor that can't confirm flame, a cracked hot surface igniter that won't light the burners, and a high-limit switch tripping because of restricted airflow from a clogged filter. Start by checking and replacing the filter; if the air stays cool, call us.
My furnace stopped and there's an error code blinking — what does it mean?
Count the blinks on the diagnostic LED through the burner sight glass without opening the panel. Each code maps to a specific safety or sensor — flame loss, pressure switch, high-limit, or ignition. Read us the count and we'll arrive knowing which part to test first.
How much does a furnace repair visit cost?
We inspect your system, find the exact root cause, and present a fixed, upfront price in writing before any work begins. No repair proceeds without your approval. Diagnostic/trip visits are billed at our published fee; you'll know that before we dispatch.
Should I repair or replace my furnace?
Flame sensors, igniters, capacitors, inducer motors, and gas valves are economical repairs on a sound furnace. Replacement makes sense when the heat exchanger is cracked, the unit is past its manufacturer life with unavailable parts, or repair bills approach a meaningful share of a new high-efficiency install. We'll lay out both honestly.
What happens after I request furnace service through the form?
Our staff reviews your request, checks technician availability, and confirms your appointment window with you directly by phone or text — we do not auto-schedule. The technician arrives, diagnoses, and quotes a fixed price in writing before any repair starts.
